Wodaplug EOC Slave + 2x2 WiFi EOC1121R4WL-R410, 600Mbps, 4xLAN, 2xF
Wodaplug EoC product is focused on the use of existing cable television (CATV) infrastructure for Internet access or broadband data transmission for the purpose of being compatible with the existing CATV (or sometimes satellite television) broadcast signals simultaneously transmitted on the same cable.
Two WiFi antennas - 802.11bgn device with 300Mbps 2x2 MIMO WiFi speed.
Wodaplug EOC Indoor Slave with 300Mbs WiFi speed router - EOC1121R4WL-R410, 600Mbps, 4*LAN, 2*F, WEB Management, VLAN, IGMP, QoS ...
New MTK based WiFi slave with 2 antennas and 300Mbps WiFi speed available - EOC1121R4WL-R410 !!! This new Realtek based version can offer same features, but need to update SW on your EOC master, can accept same template configuration. WEB based management for this new EOC WiFi slave is differnt, read new users guide!
EOC1121R4WL-R410 modem is the EOC slave based on HomePlug AV solution for Ethernet access over coax. It works together with EOC master which is based on HomePlug AV solution as well to construct a two-layer Ethernet data transmission channel on CATV coax cable, provide the Ethernet access service based on the existing coax cable networking.
EOC1121R4WL-R410 series is based on the Mstar chipset solution (510CE chip)，with high anti jamming capability OFDM technology. The 7.5-65MHz low frequency band is used for EOC signals. Built in high isolation filter as CATV RF and EOC signal mixer, the EOC signal and CATV signal in 87Mhz~1Ghz can run on one cable without interference. The PHY Layer speed is 600Mbps,the MAC Layer throughput is up to 320Mpbs.
EOC1121R4WL-R410 series WIFI is based on the MTK chipset solution. It meets 802.11 b/g/n technical standards. It has two external antenna, and can support 2.4GHz wireless signal. It has the characteristics of strong penetrating power and wide coverage. It can provide users with more efficient data transmission security.
Based on MSTAR+MTK chipsets solution of HomePlug AV and 11n WiFi technology
Work at low frequency between 7.5MHz~65MHz without influence on CATV service
Physical layer speed is 600Mbps and Max MAC layer throughout is 320Mbps
Support data encryption for both uplink and downlink
Support 4*10/100Mbps Ethernet ports auto-negotiation function
Support slave(CPE) isolation
Support VLAN configuration based on slave’s Ethernet ports and 802.1q
Support bandwidth(speed) limitation for both uplink and downlink
Support QoS configuration based on slave port or VLAN
Support broadcast storm control
Support data packages count
Automatically distribute configurations to newly connected slaves, available to use as soon as correctly connected and power on
Support WEB,CLI and SNMP management
Support on-line upgrading
default IP for management : http://192.168.1.1
For the software, there is no difference between the old and new slave. Please read new users guide. The full access and complete setting in Web could be realized via the admin access.
The new version wifi slave is more flexible in the application than before. It can controls the STB1 and STB2 ports which used as the Ethernet ports to setting the VLAN, rate-limiting, configuration,etc.
The LAN1 and LAN2 have the router feature which support the PPPoE. Moreover, The two mode can work at the same time.
Item Specification - Model Number - EOC1121R4WL-R410
Chipsets Mstar(C510E), MTK 11n
Protocol EOC standard : HomePlug AV/ IEEE P1901(Draft); Etherent protocol > IEEE 802.1Q, IEEE 802.1p, IEEE 802.3, IEEE 802.3u, IEEE 802.3x,HTTP, SNMP, TELNET
Phisycal Speed 600Mbps
Modulation Bandwidth 7.5 MHz~65 MHz
Modulation Technology OFDM-2690-carriers,4096/1024/256/64/16/8-QAM, QPSK, BPSK, ROBO
Max. Slave number 256
Encryption mode 128-bit AES encrypted
VLAN Support max. 16 VLANs
Limitation of port speed Support minimum 64Kbps granularity
QoS Support VLAN priority
Working mode CSMA/CA
Multicast support Support IGMP manage Multicast diagram
Management mode Support SNMP, WEB, CLI multi-managed mode
Ethernet Interface 4*10/100M Ports
Coax. Cable Interface 1*Female Connector, IP signal output
Ethernet Network connection indicator
Power Power connection indicator
Data Cable connection indicator
Transmit Power 0±3dBm
Reflection loss >16dB
Insertion loss less than 1dB
Receiving sensitivity -65dB
Power Consumption ≦5W
Power Supply 12VAC/5A
Working Temperature 0℃~50℃
Storage Temperature -40℃~80℃
Working Humidity 10%~90%, non-condensation
Storage Humidity 5%~90%, non-condensation
Environmental standards RoHS
Product Size 160*120*28.5mm
Product Weight N.W.: 0.5kg G.W.: 0.52kg
Operating Mode > Router or Bridge
Frequency Range : 2,412-2,472GHz
Transmitting Speed : 11n [135Mbps]:standard + 802.11b/g standard /auto-negotiation/
Operating channels qty : 13
Spread Spectrum : DSSS, CCK and OFDM
Coding BPSK, QPSK, 16QAM and 64QAM
RF Power : 802.11b: 16.5±1dBm , 802.11g: 13±1dBm @ 54 Mbps; 14±1dBm @ 48 Mbps; 15±1dBm @ 6 ~ 36 Mbps ; 802.11n: 13±1dBm @ 54 Mbps; 14±1dBm @ 48 Mbps; 15±1dBm @ 6 ~ 36 Mbps
antenna : 4dBi (fixed)
RF Receiving Sensitivity : 802.11b: -82dBm @ 1 Mbps; -80dBm @ 2 Mbps; -78dBm @ 5.5 Mbps; -76dBm @ 11 Mbps 802.11g: -82dBm @ 6 Mbps; -81dBm @ 9 Mbps; -79dBm @ 12 Mbps; -77dBm @ 18 Mbps; -74dBm @ 24 Mbps; -70dBm @ 36 Mbps; -66dBm @ 48 Mbps; -65dBm @ 54 Mbps 802.11n: -65dBm @ 65 MbpsHT40; -61dBm @ 135 MbpsHT40
Encryption Mode 802.11i Security: WEP-64/128, TKIP(WPA-PSK) and AES(WPA2-PSK)
FAQ : please visit http://www.wodaplug.com/faq/f-a-q-eoc_slavewifi/
You might also like
16 other products in the same category: